If the timer isn’t properly programmed, it may cause the softener to regenerate too often or not often enough. The water softener control will determine how often the system performs a regeneration cycle, based on your water usage and/or your hardness levels. If it’s beyond cleaning, you’ll need to consider buying a new one. It might also be useful to use white vinegar or a scale-removing cleaning product on your injector. Don’t use anything that’s hard enough to alter the hole size, though. Use something small, like a wooden toothpick, to clean it out. Inside the injector nozzle is a small orifice that regulates the brinedraw. In this case, simply remove the injector assembly and clean all of its components. Injector is CloggedĪgain, for high hardness and iron water supplies, a clogged water softener injector assembly is another possible issue. This may also become blocked, especially if your water has a high hardness or iron content. Finally, check the drain line flow control in your water softener. Cleaning will likely be required to ensure proper operation. Contaminants in the brine well may result in a clogged orifice. You might also be dealing with a clogged brine refill flow control. Proper maintenance and cleaning of the control valve should help prevent internal valve issues. If you have higher-than-average water hardness, or your water contains a lot of iron, there may be a buildup of minerals inside the control valve. If your brine line doesn’t appear to be the issue, examine the water softener’s control valve. Your owners manual should have more information about the brine line and its proper installation. The brine line connects the brine tank float valve assembly to the control valve. You can find the brine line by removing the lid of the brine tank and removing the cap from the brine well. If your brine line isn’t properly installed, it may prevent the float from being able to stop a brine tank overflow.Ĭheck that the brine line is installed properly to avoid this issue. This float valve is designed to prevent overflow of the brine tank. Inside most brine tanks is a float assembly. If the brine line appears to be damaged, replace it with a new one. The brine line might also become kinked, preventing water from flowing through. If the brine drain becomes blocked or disconnected, the tank may struggle to empty (or it may leak out of the system, which is even more of a nightmare). The brine drain is what allows the brine solution to leave the tank and enter the resin bed during regeneration cycles. The tubing must be in good condition and properly connected at the softener valve and at the brine tank float valve assembly. If this line isn’t installed correctly, it may overfill the tank due to leakage, or fail to draw brine properly and draw air into the system through the leak point. It also draws brine from the tank during the brining phase of a regeneration. The brine line delivers water to the brine tank. □ Why is My Brine Tank Not Emptying? Improperly Installed Brine Tubing This could be caused by a number of factors, which I’ve covered below. It is sometimes recommended that you add enough salt to your brine tank to completely cover the water.Ī problem has likely occurred if too much water has entered your brine tank, or your brine tank isn’t emptying. Usually, if you can see water in your brine tank, it’s a sign that you may need to add salt. This water is needed to dissolve a portion of the softener salt and form a brine solution, which flushes the captured hardness out the resin beads and replenishes them with a new charge of sodium ions. Water in your brine tank is normal – there should be around 6 to 12 inches in the average residential unit. If you can see water in the brine tank of your softener, there might not actually be an issue at all. □ Should There Be Water In My Brine Tank? If you’re dealing with excessive water, an overflowing tank, or a dip in water pressure, you’re probably facing a bigger issue. Low levels of water can be expected in some systems. There are several reasons why your water softener brine tank might be full of water – and it really depends on how you define “full”. □ Why is My Water Softener Full of Water?
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |